OCEOSmp/directive reference

From wiki
Jump to navigation Jump to search

This section is under construction

Introduction

To be added

Directives

Initialisation directives

oceos_init()

Header File
initialisation.h

Description
Initialises OCEOS and must be the first directive used.

Initialises the OCEOS system meta data using the information supplied in the application configuration and prepares for creation of tasks etc.

The values provided in the application configuration are checked as much as possible before being used.

The system log also is created here.

This function sets up sysMetaPtr and init_meta_ptr and must have completed successfully before tasks etc. can be created.

It disables interrupts and leaves them disabled, they will be re-enabled to the previous level after all tasks etc. have been created and oceos_init_finish() has completed successfully.
Prototype

/**
 * Initialises OCEOS and  must be the first directive used.
 *
 * Initialises the OCEOS system meta data using the information supplied in
 * the application configuration and prepares for creation of tasks etc.
 *
 * The values provided in the application configuration are checked as much
 * as possible before being used.
 *
 * The system log also is created here.
 *
 * This function sets up sysMetaPtr and init_meta_ptr and must have completed
 * successfully before tasks etc. can be created.
 *
 * It disables interrupts and leaves them disabled, they will be re-enabled to
 * the previous level after all tasks etc. have been created and
 * oceos_init_finish() has completed successfully.
 *
 * @param app_config Pointer to configuration struct
 * @return SUCCESSFUL                        All OK
 *         WARN_LOG_SIZE_DEFAULT             Warning, log size is set to default value of 64 entries
 *         WARN_NO_ERROR_FUNCTION            Warning, user defined function for ERROR handling is not provided
 *         ERR_CPU_FIRST_CORE_INVALID        Start CPU not in a range of available cores for this target; or greater than end CPU
 *         ERR_CPU_LAST_CORE_INVALID         Last CPU not in a range of available cores for this target
 *         ERR_NOT_START_CPU_CORE            Executing oceos_init on wrong CPU
 *         ERR_STACK_START_MISALIGNED        Stack start address is not set by user misaligned
 *         ERR_STACK_PER_CORE_INVALID        Stack per CPU size is zero, or not 8byte aligned, or less then min require
 *         ERR_LOG_ADDR_MISALIGNED           Log start address is not 8 byte aligned
 *         ERR_FIX_ADDR_MISALIGNED           Fixed area start address is not 8 byte aligned
 *         ERR_DYN_ADDR_MISALIGNED           Dynamic area start address is not 8 byte aligned
 *         ERR_CPU_CORE_RANGE_WRONG          CPU cores in use exceed available CPUs on the SoC
 *         ERR_STACK_SPACE_WRONG             Current CPU SP is not within user provided stack range
 *         ERR_LOG_SIZE_INVALID              Log size outside expected range
 *         ERR_CS_LOG_SIZE_INVALID           Context switch log size invalid
 *         ERR_TASK_NUMBER_INVALID           Number of tasks invalid
 *         ERR_MUTEX_NUMBER_INVALID          Number of mutexes invalid
 *         ERR_RWMUTEX_NUMBER_INVALID        Number of rwmutexes invalid
 *         ERR_SEM_NUMBER_INVALID            Number of semaphores invalid
 *         ERR_DATAQ_NUMBER_INVALID          Number of datqs invalid
 *         ERR_TIMED_ACTIONS_NUMBER_INVALID  Number of timed actions invalid
 *         ERR_OVERLAP_STACK                 Overlap stack end address with (two overlap areas are set)
 *         ERR_OVERLAP_LOG                   Overlap log with (two overlap areas are set)
 *         ERR_OVERLAP_FIXED                 Overlap fixed area with (two overlap areas are set)
 *         ERR_OVERLAP_DYNAMIC               Overlap dynamic area with (two overlap areas are set)
 *         ERR_FIXED_MEMORY_FAILED           Fixed area memory write fail
 *         ERR_DYNAMIC_MEMORY_FAILED         Dynamic area memory write fail
 *         ERR_TIMER_ADDR_INVALID            Timer address not provided by user (null). SPARC only
 *         ERR_SYS_TIMER_INDEX_INVALID       System timer index of subtimer invalid; SPARC only; Subtimers start from index 1; Need index of subtimer plus one in front
 *         ERR_PERIPHERAL_CLOCK_INVALID      System peripheral code invalid
 *
 */
S32_t   oceos_init(
    const struct application_configuration app_config
);

Parameters

Parameter Description
app_config Pointer to configuration struct. struct application_configuration defined in basic_structs.h

Returns
This function returns S32_t with one of the status codes defined above.

Example Usage

    /*
     * Create the application configuration structure
     */
    struct application_configuration           app_config = {0};

    /*
     * Fill in the application parameters
     */
    app_config.log_address                   = (log_t)log_data;              // required
    app_config.fixed_data_address            = (adrs_t)fixed_data;            // required
    app_config.dynamic_data_address          = (adrs_t)dynamic_data;          // required

    app_config.stack_start_address           = start_stack_array[OCEOS_START_CPU_INDEX];// OCEOSMP_STACK_START_ADDRESS;
    app_config.stack_size_per_cpu            = (U32_t)&__oceos_stack_size_per_cpu;  // OCEOSMP_STACK_LOW_BOUND_ADDRESS;

    app_config.system_error_function         = oceosmp_on_error;               // NULL => ignore
    app_config.log_full_function             = oceosmp_on_full_log;            // NULL => ignore

    // used in setting up system log and fixed data array
    app_config.log_number_of_entries         = NUMBER_OF_LOG_ENTRIES;          // 0 => use default

    app_config.number_of_tasks               = NUMBER_OF_TASKS;                // >= 1

    app_config.number_of_mutexes             = NUMBER_OF_MUTEXES;
	app_config.number_of_rwmutexes			 = NUMBER_OF_RWMUTEXES;
    app_config.number_of_counting_semaphores = NUMBER_OF_SEMAPHORES;
    app_config.number_of_data_queues         = NUMBER_OF_DATAQS;

    /**
     * FOR SPARC TARGET ONLY.
     */
    app_config.sys_time_timer_index          = SYS_TIME_TIMER_INDEX;           // 0 => invalid index
    /**
     * FOR SPARC TARGET ONLY.
     * Not Used for ARM. Always Nested
     */
    app_config.interrupt_nesting_enabled     = TRUE;                           // TRUE => single vector
    app_config.oceos_cpu_switch_int_number   = OCEOS_CPU_INTER_COM_INT_NUMBER; // User should provide SGI ID (0-15)

    app_config.timed_actions_queue_size      = NUMBER_OF_ACTION_ENTRIES;
    app_config.CS_log_entries_base2          = CS_LOG_DEF_ENTRIES_BASE2;
    /**
     * Set starting index of CPU that will be used by OCEOSMP
     */
    app_config.oceos_cpu_start_index         = OCEOS_START_CPU_INDEX;
    /**
     * Set last index of CPU that will be used by OCEOSMP
     */
    app_config.oceos_cpu_last_index          = OCEOS_LAST_CPU_INDEX;
    /*
     * Set system/peripheral clock used to initialise system timer
     */
    app_config.soc_peripheral_clck           = BSP_SYSFREQ * 1000 * 1000;

    // initialise OCEOSMP
    S32_t status;
    status = oceos_init(app_config);
    if (OCEOS_SUCCESS > status) {
      oceosmp_print("\n oceos_init failure\n\r");
      return 0;
    } else {
      return 1;
    }   // else

oceos_init_finish()

Header File
initialisation.h

Description
Finalizes the fixed data array after all tasks etc. have been created

All information needed to start OCEOS can be found in the fixed data area when oceos_init_finish() has completed.

Once all tasks etc. have been created oceos_init_finish() checks the accumulated information against the application configuration data stored in the fixed meta structure.

oceos_init_finish also calculates the size of the dynamic data area and checks it does not overlap with the system stack, the system log, or the fixed data, and if all ok sets up pointers to the various dynamic area components in the fixed data.

It then adds an XOR checksum to the fixed data area, and checks that this is followed by FILLER, which it replaces with the end sentinel.

On successful completion it restores the interrupt level to its value before oceos_init() was called, otherwise interrupts remain disabled.

Prototype

/**
 * Finalizes the fixed data array after all tasks etc. have been created
 *
 * All information needed to start OCEOS can be found in the fixed data area
 * when oceos_init_finish() has completed.
 *
 * Once all tasks etc. have been created oceos_init_finish() checks the
 * accumulated information against the application configuration data
 * stored in the fixed meta structure.
 *
 * oceos_init_finish also calculates the size of the dynamic data area and
 * checks it does not overlap with the system stack, the system log, or the
 * fixed data, and if all ok sets up pointers to the various dynamic area
 * components in the fixed data.
 *
 * It then adds an XOR checksum to the fixed data area, and checks that this
 * is followed by FILLER, which it replaces with the end sentinel.
 *
 * On successful completion it restores the interrupt level to its value
 * before oceos_init() was called, otherwise interrupts remain disabled.
 *
 * @return  OCEOS_SUCCESS                             All OK
 *          ERR_SYS_FIXED_CORRUPT               System Meta data is NULL or corrupt
 *          ERR_SYS_DYN_CORRUPT                 System Dynamic area corrupt
 *          ERR_WRONG_CPU_CORE                  Executing directive on wrong CPU
 *          ERR_WRONG_PHASE                     Called before oceos_init()
 *          ERR_TASKS_INCOMPLETE                Created wrong number of tasks
 *          ERR_MUTEX_INCOMPLETE                Created wrong number of mutexes
 *          ERR_RWMUTEX_INCOMPLETE              Created wrong number of rwmutexes
 *          ERR_SEM_INCOMPLETE                  Created wrong number of semaphores
 *          ERR_DATAQ_INCOMPLETE                Created wrong number of dataqs
 *          ERR_TASK_MAX_ID_INVALID             Task's max id invalid
 *          ERR_MUTEX_MAX_ID_INVALID            Mutexe's max id invalid
 *          ERR_RWMUTEX_MAX_ID_INVALID          Rwmutexe's max id invalid
 *          ERR_SEM_MAX_ID_INVALID              Semaphore's max id invalid
 *          ERR_DATAQ_MAX_ID_INVALID            Dataq's max id invalid
 *          ERR_TOTAL_JOBS_NUMBER_WRONG         Wrong number of total jobs created
 *          ERR_ORDER_ARRAY_PTR_INVALID         Order array pointer is NULL or mis-aligned
 *          ERR_FIXED_AREA_TOO_SMALL            Not enough space for fixed data area
 */
S32_t   oceos_init_finish(void);

Parameters
There are no input parameters to this function.

Returns
This function returns an S32_t with one of the status codes defined above.

Example Usage

    /*
     * Finish initialising OCEOS and setting up the fixed data
     */
    status = oceos_init_finish();
    if(OCEOS_SUCCESS > status){
        // LOG
      oceosmp_print("\nAbandoning, problem ending OCEOS initialisation\n\r");
        return -1;
    }   // if

oceos_start()

Header File
initialisation.h

Description
Starts OCEOS scheduling.
Create dynamic OCEOS structures and start scheduling.
This function should only be called once and only after oceos_init() and oceos_init_finish() have been called successfully.
Normally this function does not return.
If a problem is detected the function terminates and returns an appropriate DIRECTIVE_STATUS code, with interrupts disabled.

Prototype

/**
 * Starts OCEOS scheduling
 *
 * Create dynamic OCEOS structures and start scheduling
 *
 * This function should only be called once
 * and only after oceos_init()
 * and oceos_init_finish() have
 *  been called successfully.
 * Normally this function does not return.
 * If a problem is detected the function
 * terminates and returns an appropriate
 * DIRECTIVE_STATUS code, with interrupts disabled.
 *
 * @param fixed_array_ptr   Pointer to fixed data array
 * @param start_task        Task ID
 * @param data_ptr          Pointer to data to be passed to the task
 * @return  OCEOSMP_EXIT                        OCEOSMP return from scheduling and exit
 *          ERR_SYS_FIXED_CORRUPT               Fixed area pointer is null or bad sentinel
 *          ERR_FIXED_AREA_SIZE_WRONG           Fixed area size is zero
 *          ERR_FIXED_AREA_END_SENTINEL_BAD     Fixed data end sentinel corrupt
 *          ERR_FIXED_AREA_BAD_XOR              Fixed area bad checksum or checksum mis-match
 *          ERR_INIT_NOT_DONE                   oceos_start() called without initialisation
 *          ERR_DYN_AREA_PTR_BAD                Dynamic area pointer invalid in sysMetaPtr
 *          ERR_INT_HANDLER_BAD                 IRQ controller pointer provided by BCC is NULL;or OCEOS handler is not set
 *          ERR_DYN_JOB_PTR_BAD                 Job array pointer is NULL
 *          ERR_FIXED_TASK_PTR_BAD              Tasks array pointer is NULL
 *          ERR_JOB_COUNT_WRONG                 Total job count inconsistent
 *          ERR_DYN_MUTEX_PTR_BAD               Mutex dynamic pointer is NULL
 *          ERR_DYN_LOCK_PTR_BAD                Mutex lock array pointer is NULL
 *          ERR_DYN_RWMUTEX_PTR_BAD             Rwmutex dynamic pointer is NULL
 *          ERR_DYN_RWLOCK_PTR_BAD              Rwmutex lock array pointer is NULL
 *          ERR_FIXED_SEM_PTR_BAD               Semaphore fixed pointer is NULL
 *          ERR_DYN_SEM_PTR_BAD                 Semaphore dynamic pointer is NULL
 *          ERR_SEM_PEND_PTR_BAD                Semaphore pending queue pointer is NULL
 *          ERR_FIXED_DATAQ_PTR_BAD             Dataq fixed pointer is NULL
 *          ERR_DYN_DATAQ_PTR_BAD               Dataq dynamic pointer is NULL
 *          ERR_DATAQ_PEND_PTR_BAD              Dataq pending queue pointer is NULL
 *          ERR_DATAQ_DATA_PTR_BAD              Dataq data pointer is NULL
 *          ERR_CPU_INT_NUMBER_INVALID          SPARC only.IRQ number for CPU inter-comunication invalid(zero or used by timer)
 *          ERR_REGISTER_CPU_IRQ_FAILED         SPARC only. Failed to set CPU IRQ handler in BCC
 *          ERR_CPU_STACK_INVALID               Current CPU stack not within specified range
 *          ERR_CPU_PRIORITY_STACK_INVALID      Per CPU priority stack invalid
 *          ERR_LOG_AREA_END_SENTINEL_BAD       Log area end sentinel override
 *          ERR_TA_CONFIG_PTR_BAD               SPARC only; Timed action configuration data pointer is NULL
 *          ERR_TA_TIMER_INDEX_INVALID          SPARC only; Timed action sub-timer index in timer unit is invalid
 *          ERR_TA_IRQ_NUMBER_INVALID           SPARC only; Timer action timer IRQ number is invalid
 *          ERR_TA_BCC_IRQ_REGISTER_FAILED      SPARC only; Timed action timer IRQ handler failed to register
 */
S32_t   oceos_start(
    const U32_t * const fixed_array_ptr,// pointer to fixed data array
    const U32_t start_task,             // taskID
    void * const data_ptr               // pointer to data to be passed to task
);

Parameters

Parameter Description
fixed_array_ptr Pointer to fixed data array
start_task Task ID
data_ptr Pointer to data to be passed to the task

Returns
This function returns S32_t with one of the status codes defined above.

Example Usage

/* Sample Task names - all here start with t_ to help avoid name confusion */
enum TASK_NAME{
    t_tom,                      // will have task ID 0
    t_dick,                     // will have task ID 1
};
extern U32_t fixed_data[];
...
S32_t status;

status = oceos_start(fixed_data, t_tom, NULL);

oceos_exit()

Header File
initialisation.h

Description
Ends scheduling and exit from oceos_start(). No task can be started after this.
OCEOS will exit when the current job ends.
An idle task in an endless loop should check that scheduling is enabled.

Prototype

/**
 * Ends scheduling and exit from oceos_start.
 * No task can be started after this.
 * OCEOS will exit when the current job ends.
 * An idle task in an endless loop should check that scheduling is enabled.
 *
 * @return  OCEOS_SUCCESS
 *          ERR_SYS_FIXED_CORRUPT       System Fixed area corrupt
 *          ERR_WRONG_PHASE             Called before scheduling started
 */
S32_t oceos_exit(void);

Parameters
There are no input parameters to this function.

Returns
This function returns S32_t with one of the status codes defined above.

Example Usage

// Exit OCEOS
oceos_exit();

oceos_CPU_sleep()

Header File
initialisation.h

Description
Puts CPU in sleep mode.
User must to be sure that interrupts are enabled.

Prototype

/**
 * Puts CPU in sleep mode.
 * User must to be sure that interrupts are enabled.
 *
 * @return  OCEOS_SUCCESS
 */
S32_t oceos_CPU_sleep(void);

Parameters
There are no input parameters to this function.

Returns
This function returns an S32_t with one of the status codes defined above.

Example Usage

// Put CPU to sleep
oceos_CPU_sleep();

oceosmp_cpu_disable()

Header File
initialisation.h

Description
This function ends execution of all tasks running on particular CPU and removes the CPU from scheduling.

Prototype

/**
 * Ends execution of all tasks running on particular CPU and removes this CPU from scheduling.
 * @param cpu_id
 * @return  OCEOS_SUCCESS
 *          ERR_SYS_FIXED_CORRUPT       System Fixed area corrupt
 *          ERR_SYS_DYN_CORRUPT         System Dynamic area corrupt
 *          ERR_WRONG_PHASE             Directive was called before OCEOS initialisation is finished
 *          ERR_ID_INVALID              CPU ID outside allowed range 0 to 254
 *          ERR_ID_WRONG                CPU ID >= number of available CPUs
 *          ERR_CPU_ALREADY_DISABLED    CPU already disabled
 */
S32_t oceosmp_cpu_disable(
    U32_t cpu_id
);

Parameters

Parameter Description
cpu_id ID of CPU core to be disabled.

Returns
This function returns an S32_t with one of the status codes defined above.

Example Usage

S32_t status, faulty_cpu;
...
// Disable faulty CPU core
status = oceosmp_cpu_disable(faulty_cpu));

oceosmp_cpu_enable()

Header File
initialisation.h

Description
This function adds a disabled CPU core to the OCEOSmp scheduler. It should only be called after scheduling has started

Prototype

/**
 *  Adds disabled CPU to OCEOSmp scheduler
 *
 *  N.B. This function should only be called after scheduling has started
 *
 * @param cpu_id
 *
 * @return  OCEOS_SUCCESS
 *          ERR_SYS_FIXED_CORRUPT       System Fixed area corrupt
 *          ERR_SYS_DYN_CORRUPT         System Dynamic area corrupt
 *          ERR_WRONG_PHASE             Directive was called before OCEOS initialisation is finished
 *          ERR_ID_INVALID              CPU ID outside allowed range 0 to 254
 *          ERR_ID_WRONG                CPU ID >= number of available CPUs; or the same as currently running
 *          ERR_CPU_ALREADY_ENABLED     CPU already enabled
 */
S32_t oceosmp_cpu_enable(
    U32_t cpu_id
);

Parameters

Parameter Description
cpu_id ID of CPU core to be enabled.

Returns
This function returns an S32_t with one of the status codes defined above.

Example Usage

S32_t status, good_cpu;
...
// Enable CPU core
status = oceosmp_cpu_enable(good_cpu));

oceosmp_cpu_terminate()

Header File
initialisation.h

Description
This function removes a CPU core from the OCEOSmp scheduler and marks it so it cannot be restarted. It puts CPU to sleep with interrupts disabled. It should only be called after scheduling has started.

Prototype

/**
 *  Removes CPU from OCEOSMP scheduler and terminates, cannot be restarted.
 *  Puts CPU to sleep with interrupts disabled
 *
 *  N.B. This function should only be called after scheduling has started
 *  Steps:
 *     1. Set terminate flag on this CPU;
 *     2. Trigger software interrupt to transfer execution to IRQ handler;
 *     3. Check flag and if set => put CPU to sleep in while loop with interrupts disabled;
 *     4. Set MAX priority on this CPU priority stack;
 *     5. Remove CPU from scheduling;
 *     6. Clean up all the tasks by calling task terminate function and free up all the
 *        preempted jobs by this CPU;
 *
 * @param cpu_id
 *
 * @return  OCEOS_SUCCESS
 *          ERR_SYS_FIXED_CORRUPT       System Fixed area corrupt
 *          ERR_SYS_DYN_CORRUPT         System Dynamic area corrupt
 *          ERR_WRONG_PHASE             Directive was called before OCEOS initialisation is finished
 *          ERR_ID_INVALID              CPU ID outside allowed range 0 to 254
 *          ERR_ID_WRONG                CPU ID >= number of available CPUs; or the same as currently running
 *          ERR_CPU_ALREADY_TERMINATED  CPU already terminated
 */
S32_t oceosmp_cpu_terminate(
    U32_t cpu_id
);

Parameters

Parameter Description
cpu_id ID of CPU core to be terminated.

Returns
This function returns an S32_t with one of the status codes defined above.

Example Usage

S32_t status, faulty_cpu;
...
// Terminate CPU core
status = oceosmp_cpu_terminate(faulty_cpu));

Task directives

API Functions
Directive Description main task IRQ handler
oceos_task_create() Create Task *
oceos_task_start() Start Task * *
oceos_task_timed_start() Schedule a task to start execution at a given system time * *
oceos_task_disable() Disable Task * *
oceos_task_enable() Enable Task * *
oceos_task_self() Returns the task ID of the currently executing task * *
oceos_task_get_priority() Get priority of a task * *
oceos_task_get_status() Get status of a task * *
oceos_task_kill() Directive to terminate current task * *
oceos_task_get_info() Get task information * *

Task data structures

Header File
tasks.h

Description
The following data structures are used by some of the task directives.

Data structures

/**
 * A pointer to this structure is passed to oceos_task_create().
 * The structure is first initialised according to a tasks's parameters,
 * and is not used again after the task is created and may then be discarded.
 */
struct task_descriptor {

	void (*function_start)(void*);	// name of task start function
	void (*function_end)(void*);	// optional, NULL or task end function

	U32_t task_id;					// 0 to 254, usually an enum
	U32_t task_jobs_max;			// 1 to 15, max concurrent 'jobs'
	U32_t task_priority;			// 1 (highest) to 254 (lowest)
	U32_t task_threshold;			// >=1, <= task_priority (higher or same priority)
	U32_t task_turned_on_initially;	// 0: disabled initially, else enabled

	U32_t time_deadline_microsecs;	// start request to finish, 0 to ignore
	U32_t time_min_interval_microsecs;	// between start requests, 0 to ignore

	U32_t uses_cpu_affinity;		// 0: not restricted, else core restricted
	U32_t uses_cpu_affinity_core_id;// core ID to which restricted if affinity used
}__attribute__ ((aligned (8)));

/**
 * Task info used with oceos_task_get_info
 */
struct task_info {
  U64_t           time_max_delay;               // maximum time job is waiting on ready queue before becoming active
  U64_t           time_max_finish;              // maximum time to finish job execution after starting
  U64_t           time_max_exec;                // maximum time spent executing
  U64_t           time_total_exec;              // total CPU time used by this task
  U64_t           time_min_gap_starts;          // minimum time between job creations, can be reset
  U64_t           time_min_gap_finish_start;    // minimum time between job ending and new job creation, can be reset

  U64_t           time_last_start;              // time of most recent job creation
  U64_t           time_last_finish;             // time of most recent job finish

  unsigned int    jobs_current_max  :16;        // maximum number of current jobs for this task, no roll over, can be reset
  unsigned int    jobs_total        :16;        // number of times this task was started, no roll-over, can be reset
  U32_t           jobs_current;                 // Number of task instances currently in use by oceos

  U32_t           preempt_max;                  // maximum times any job was pre-empted, no roll-over, can be reset
}__attribute__ ((aligned (8)));

oceos_task_create()

Header File
tasks.h

Description
Create a task. Can only be use before OCEOS starts. Stores the task information in the OCEOS fixed data area. This directive populates the data structures for a task. It should be called after oceos_init() and before oceos_init_finish().
It must be called for each task otherwise oceos_start() will return an error.

Prototype

enum DIRECTIVE_STATUS   oceos_task_create(
    unsigned int taskID,         // unique, 0 to TASKS_MAX_ID
    U32_t priority,              // TASK_MAX_PRIORITY to TASK_MIN_PRIORITY
    U32_t threshold,             // TASK_MAX_PRIORITY to priority
    U32_t jobs_max,              // 1 to JOBS_MAX
    BOOLE_t FP_used,             // whether uses floating point hardware
    BOOLE_t initially_enabled,   // whether task enabled initially
    void (void *) start_function,// task start address
    void (void *) end_function,  // start of task end function
    U32_t time_deadline,         // maximum time to complete (ignore if 0)
    U32_t time_mininterstart     // minimum time between start requests
 );

Parameters

Parameter Description
taskID Unique task ID from 0 to TASKS_MAX_ID
priority TASK_MAX_PRIORITY to TASK_MIN_PRIORITY
threshold TASK_MAX_PRIORITY to priority
jobs_max Number of 1 to JOBS_MAX
FP_used whether uses floating point hardware
initially_enabled whether task enabled initially
start_function task start address
end_function start of task end function
time_deadline maximum time to complete (ignore if 0)
time_mininterstart minimum time between start requests

Returns
This function returns enum DIRECTIVE_STATUS.

enum DIRECTIVE_STATUS Description
INCORRECT_STATE Init Meta Pointer is NULL or

Pointer to Task fixed data is NULL

TOO_MANY Exceeds number of MAX Tasks or

Exceeds number of MAX Jobs

INTERNAL_ERROR System Meta pointer is NULL or

System Meta pointer start sentinel is corrupt

INVALID_ID Failed on task ID check
INVALID_NAME Task ID is already in use
INVALID_PRIORITY Failed on task priority check
INVALID_NUMBER Failed on task threshold check
INVALID_SIZE Failed on task max job check
SUCCESSFUL All is OK

Example Usage

 enum TASK_NAME{
    t_tom,                      // will have task ID 0
    t_dick,                     // will have task ID 1
 };
 extern int task_tom_start(void* data);
 ...
 enum DIRECTIVE_STATUS status;
    // Task 0: priority 10, max jobs 1, enabled (consumer task)
    status  = oceos_task_create(t_tom, // unique, 0 to TASKS_MAX_ID  
	                               10, // TASK_MAX_PRIORITY to TASK_MIN_PRIORITY
								   10, // TASK_MAX_PRIORITY to priority
								    1, // 1 to JOBS_MAX
								    0, // whether uses floating point hardware
				         TASK_ENABLED, // whether task enabled initially
				       task_tom_start, // task start address
						         NULL, // start of task end function
						            0, // maximum time to complete (ignore if 0)
						            0  // minimum time between start requests
				                    );