OCEOSmp/blank
Next Section
Logging directives
Introduction
Log Area Features (for details of other areas see oceos_areas.h)
The system log area holds the system log and the records of the present and previous values of the system state variable.
It is set up initially as an array of 32-bit words that starts at a 32-bit aligned address provided by the application developer.
It is recommended that this address be in non-volatile RAM memory if this is available to allow information be preserved across power-up cycles.
OCEOS preserves log area information across resets as far as possible.
The system log itself is a circular buffer of struct log entry. Older entries are overwritten by new entries once all entries are in use.
The application developer can specify a function to be called when 3/4 of log entries are in use. This function is called again only after 3/4 of log entries have been read and the log has again become 3/4 full.
The read and write indices are stored in the log area and if equal indicate that the log is empty.
As with other OCEOS data areas, the log area starts with a header
- a 32-bit word holding a constant OCEOS_VERSION
- a 32-bit word holding the log area size in 32-bit words
- a 32-bit word, the system status variable
- a 32-bit word, the system status mask
- a 32-bit word, the accumulated system status
- a 32-bit word, the previous system status mask
- a 32-bit word, the log control, that gives whether the log full function was called
- the read index
- the write index
- an array of struct log_entry making up the system log itself
- ending with a 32-bit constant END_SENTINEL
The system fixed meta structure at sysMetaPtr provides
- system_log_ptr the start address of the log area
- logEntries the number of log entries
- logCreated flag indicating log was created successfully
- logFullFunction user defined function, called when the log becomes 3/4 full (or NULL if not used)
Log Entry Types and Structure
/***************************************************************************** * LOG ENTRY TYPES * * A log entry type is an 8-bit number. * Values from 0 to 127 can be defined by the application. * Values from 128 to 255 are used by OCEOS as below. * * * NOTE: Add new log types at the end for backward compatibility */ enum LOG_ENTRY_TYPE{ LOG_SYS_OK = 0x80U, LOG_OCEOS_ABORT, // when exiting from oceos_start LOG_LOG_NOT_VALID_ENTRY, // used to initialise log and when log empty LOG_INIT_TASK_START_FAIL, // initial task passed to oceos_start failed LOG_DEADLINE_MISSED, // task deadline missed LOG_JOB_NOT_ACTIVE, // cpu_terminate but job not active, absurd LOG_JOB_NOT_FREE, // job guarded but not free LOG_JOBS_INC_FAILED, // pending jobs increment failed LOG_JOB_NOT_GUARDED, // paranoia LOG_CS_LOG_SPIN_FAIL, // oceos_CPU_sleep, trying to update CS log LOG_MUTEX_ALREADY_HELD, // oceos_mutex_wait, code returned, not needed LOG_MUTEX_INCORRECT_ORDER, // oceos_mutex_wait LOG_MUTEX_EXIT_HOLDING, // task exits holding one or more mutexes LOG_MUTEX_EXIT_NONE, // __oceos_tasks_remove_mutexes called but no mutex held LOG_SEMAPHORE_PENDING_REMOVE_FAIL, // timed_action.c LOG_SEMAPHORE_PENDING_QUEUE_FULL, // __oceos_semaphore_add_pend LOG_SEMAPHORE_SPIN_FAILED, // trying to access semaphore LOG_DATAQ_PENDING_QUEUE_FULL, LOG_DATAQ_PENDING_REMOVE_FAIL, LOG_DATAQ_SPIN_FAILED, LOG_TIMED_ACTION_TIMER_NULL, LOG_TIMED_ACTION_INVALID, LOG_TIMED_ACTION_BAD_INDEX, LOG_TIMED_ACTION_MISSED, LOG_TIMED_ACTION_Q_EMPTY, LOG_TIMED_ACTION_REMOVE_FAIL, LOG_TIMED_ACTION_BAD_JOB_ID, LOG_TIMED_Q_SPIN_FAIL, LOG_SYSTEM_ERROR, LOG_ATOMICINC_FAILED, LOG_PENDING_PRI_UPDATE_FAILED, LOG_KILL_TASK_INVALID_ID, // Tried to kill task with invalid ID LOG_OCEOS_EXIT_REQUEST, // oceos_exit command was called LOG_RWMUTEX_NOT_RETURNED, LOG_RWMUTEX_NOT_HIGHEST }; /***************************************************************************** * Structures */ /** * Log entry structure */ struct log_entry{ U64_t time64; unsigned int entry_cpu :8; unsigned int entry_type :8; unsigned int entry_note :16; // not used at present U32_t entry_comment; }__attribute__ ((aligned (8)));oceos_log_add_entry()
Header File
system_log.h
Description
This function adds an entry to the log. The entry overwrites the oldest unread entry if the log is full. Custom log entries can be added to enum LOG_ENTRY from 0 to 128. The indices are incremented in a circular fashion. If the write index reaches the read_index the read index is moved on, as read and write indices equal would indicate an empty log.Prototype
/** * Add an entry to the log. * this overwrites the oldest unread entry if the log is full. * Custom log entries can be added to enum LOG_ENTRY from 0 to 128 * * N.B. The indices are incremented in a circular fashion. * If the write index reaches the read_index the read index is moved on, * as read and write indices equal would indicate an empty log. * * @param type enum LOG_ENTRY_TYPE * @param info extra information to be logged * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT System Log area corrupt * ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called * ERR_ID_INVALID Log type invalid * ERR_SYS_BUSY Failed to acquire log guard * ERR_LOG_INDEX_WRONG Read/write log index is wrong */ S32_t oceos_log_add_entry( enum LOG_ENTRY_TYPE type, // 8 bits enum LOG_ENTRY_TYPE const U32_t info // information );Parameters
Parameter Description enum LOG_ENTRY_TYPE Log entry type (see previous section for a list) U32_t with the log information Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
Error bit Description ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT System Log area corrupt ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called ERR_ID_INVALID Log type invalid ERR_SYS_BUSY Failed to acquire log guard ERR_LOG_INDEX_WRONG Read/write log index is wrong Example Usage
S32_t status, info; ... // Log LOG_APP_COMMS__ERROR (defined in enum LOG_ENTRY_TYPE) and info with more details status = oceos_log_add_entry(LOG_APP_COMMS__ERROR, info);oceos_log_get_indexed_entry()
Header File
system_log.h
Description
This function returns the entry at the specified position in the log. The entry is not removed and the log and log indices are not changed. One use of this function is to allow the log be examined after a reset.Prototype
/** * Returns the entry at the specified position in the log. * The entry is not removed and the log and log indices are not changed. * (intended to allow the log be examined for example after reset) * * @param index position in the log * @param outputPtr pointer to return log entry * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT System Log area corrupt * ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called * ERR_LOG_INDEX_WRONG Read log index is wrong * ERR_LOG_DATA_PTR_BAD Data holder pointer is null */ S32_t oceos_log_get_indexed_entry( const unsigned int index, struct log_entry * const outputPtr );Parameters
Parameter Description index U32_t with position in the log outputPtr pointer to struct log_entry to hold the returned entry Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT System Log area corrupt ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called ERR_LOG_INDEX_WRONG Read log index is wrong ERR_LOG_DATA_PTR_BAD Data holder pointer is null Example Usage
S32_t status, index; struct log_entry store_entry; ... // Read log_entry at specified index into outputPtr status = oceos_log_get_indexed_entry(index, &store_entry);oceos_log_remove_entry()
Header File
system_log.h
Description
This function reads and removes the oldest unread log entry. If the log is not empty use the entry at the read index to update the value at the output pointer, returning OCEOS_SUCCESS. If outputPtr is NULL, entry is removed but no returned. If the log is empty, set the value at the output pointer to LOG_LOG_NOT_VALID_ENTRY and return ERR_LOG_EMPTY.Prototype
/** * Read and remove the oldest unread log entry * * If the log is not empty use the entry at the read index to update the value * at the output pointer, returning OCEOS_SUCCESS. * * If outputPtr is NULL, entry is removed but no returned * * If the log is empty, set the value at the output pointer to LOG_LOG_NOT_VALID_ENTRY * and return ERR_LOG_EMPTY * * @param outputPtr pointer to struct log_entry * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT System Log area corrupt * ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called * ERR_SYS_BUSY Failed to acquire log guard * ERR_LOG_INDEX_WRONG Read/write log index is wrong * ERR_LOG_EMPTY Log is empty */ S32_t oceos_log_remove_entry( struct log_entry * const outputPtr );Parameters
Parameter Description outputPtr pointer to struct log_entry Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
Error bit Description ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT System Log area corrupt ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called ERR_SYS_BUSY Failed to acquire log guard ERR_LOG_INDEX_WRONG Read/write log index is wrong ERR_LOG_EMPTY Log is empty Example Usage
S32_t status; struct log_entry *outputPtr; ... // Read log_entry into outputPtr and remove the oldest unread log entry status = oceos_log_remove_entry(outputPtr);oceos_log_reset()
Header File
system_log.h
Description
This function sets all log entries to LOG_LOG_NOT_VALID_ENTRY and the log to empty, with the read and write indices set to 0. The log is empty if the index of the next write is the same as the index of the next read. It does not affect the system status variable. It does not affect the context switch log.Prototype
/** * oceos_log_reset() * * Set all log entries to LOG_LOG_NOT_VALID_ENTRY and the log to empty, with the * read and write indices set to 0. and function called flag 0 * * The log is empty if the index of the next write * is the same as the index of the next read. * * Does not affect the system status variable * Does not affect the context switch log * * N.B The fixed data area may no longer be writable * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT System Log area corrupt; reset failed * ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called * ERR_SYS_BUSY Failed to acquire log guard */ S32_t oceos_log_reset(void);Parameters
There are no input parameters to this function.Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
Error bit Description ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT System Log area corrupt; reset failed ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called ERR_SYS_BUSY Failed to acquire log guard Example Usage
S32_t status; ... // Clear down the system log status = oceos_log_reset();oceos_log_get_size()
Header File
system_log.h
Description
This function returns the number of entries in the log according to the current values of the read and write indices. The value will be zero if the current values of the read and write indices are the same. There may still be useful information in the log, e.g. after system reset, this can be accessed using oceos_log_get_indexed_entry().Prototype
/** * Return the number of entries in the log * according to the current values of the read and write indices. * * The value will be zero if the current values of the read and write indices * are the same. * * There may still be useful information in the log, e.g. after system reset, * this can be accessed using oceos_log_get_indexed_entry() * * @param l_size pointer to log size holder * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT System Log area corrupt; * ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called * ERR_LOG_DATA_PTR_BAD Pointer to log size holder is NULL * ERR_LOG_INDEX_WRONG Read/write log index is wrong */ S32_t oceos_log_get_size( U32_t *l_size );Parameters
Parameter Description l_size U32_t pointer where size will be written. Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT System Log area corrupt; ERR_WRONG_PHASE Log directive called in wrong phase; can be used after oceos_init() called ERR_LOG_DATA_PTR_BAD Pointer to log size holder is NULL ERR_LOG_INDEX_WRONG Read/write log index is wrong Example Usage
S32_t status, size; ... // Clear down the system log status = oceos_log_get_size(&size);System State Variable and System State Mask
The System State variable provides a record of anomalies or problems detected by OCEOSmp's automatic consistency checks. An application handler for these can be set to be called automatically.
An anomaly or problem results in a flag bit being set in the 32-bit word used to store the system state variable. The flags are identified below.
All flags are reset to zero by oceos_init() when OCEOSmp is initialised, and may also be reset by the application using the directive provided.
To provide a record across OCEOSmp restarts a copy is updated automatically whenever the state variable is updated. This is not cleared by oceos_init() but may be cleared by the application using a directive.
Application software can define a problem handling function to be called automatically when specified system state flags are set. The flags are specified by setting the corresponding bits in the system state mask. The function and the state mask are defined in the system configuration.
Changing a state flag from clear to set results in the function being called (if defined). Subsequent settings of that flag have no effect until after it has been cleared using the directive provided.
N.B. In many cases when OCEOSmp sets a System State flag it also makes an entry in the system log that provides further information.
SYSTEM STATE VARIABLE FLAGS
These flags are updated by OCEOSmp using inclusive 'OR' when a consistency check detects a problem or anomaly. A copy of the system state variable is updated also and accumulates a record of flag settings that is preserved across restarts of OCEOSmp. OCEOSmp restarts reset the system state variable but not the copy.
Resetting the state variables is the responsibility of the application (except for the state variable reset done when OCEOSmp is restarted).
System Status Bits
#define STATUS_NORMAL 0u // No flag set YES #define STATUS_INVALID 0xffffffffu // System status is invalid YES BUT NO DETAIL!!! #define STATUS_MASK_NORMAL 0xffffffffu // Always call user def fn YES /* Task related problems */ #define STATUS_DISABLED_TASK_START 0x1U // An attempt to start a disabled task #define STATUS_TASK_JOB_LIMIT_OVER 0x2U // An attempt to execute a task when its jobs limit is already reached. #define STATUS_JOB_OVER_TIME 0x4U // Job time from creation to completion exceeds allowed maximum for task. YES #define STATUS_JOB_INTERVAL_SHORT 0x8U // Minimum time between job creations is less than the allowed minimum for task #define STATUS_READYQ_FULL 0x10U // Ready queue unable to accept job as result of being full #define STATUS_READYQ_NO_REMOVE 0x20U // Remove job from ready queue failed /* Mutex related problems */ #define STATUS_MUTEX_ALREADY_HELD 0x40U // Mutex wait() when mutex already held #define STATUS_MUTEX_NOT_HELD 0x80U // Mutex signal() when not already held #define STATUS_MUTEX_NOT_RETURNED 0x100U // Mutex not returned before job terminates #define STATUS_MUTEX_NOT_NESTED 0x200U // Use of multiple mutexes not nested /* Counting semaphore and data queue related problems */ #define STATUS_SEMAPHORE_JOBS_FULL 0x400U // Attempt to add job to semaphore pending list when list full #define STATUS_DATAQ_JOBS_FULL 0x800U // Attempt to add job to data queue pending list when list full #define STATUS_DATAQ_FULL 0x1000U // Data queue write when queue already full /* Timed actions related problems */ #define STATUS_TIMED_JOBS_FULL 0x2000U // Timed actions queue already full for timed task start #define STATUS_TIMED_OUTPUT_FULL 0x4000U // Timed actions queue already full for timed output #define STATUS_TIMED_ACTION_LATE 0x8000U // Timed action late YES /* Default trap handler should have been replaced * NOT USED AT THE MOMENT*/ #define STATUS_SYSTEM_ERROR 0x10000U // ERROR was handled by default trap handler YES /* Flag to indicate problem with Stack Pointer * NOT USED AT THE MOMENT*/ #define STATUS_SP_WARNING 0x20000U // SP not in expected range /* Log system error */ #define STATUS_BAD_LOG 0x40000U // System log problem #define STATUS_SPIN_FAILED 0x80000U // Get SPIN lock failed /* Not using next few bits */ /* Will have to exit */ #define STATUS_BAD_SENTINEL 0x40000000U // Area sentinel corrupt #define STATUS_BAD_META_PTR 0x80000000U // Null meta pointeroceos_system_state_get()
Header File
system_log.h
Description
This function returns of the system state variable.Prototype
/** * Returns the value of the system state variable * * @param state pointer to state holder * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_LOG_DATA_PTR_BAD Data holder pointer is null * ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null */ S32_t oceos_system_state_get( U32_t *state // pointer to state holder );Parameters
Parameter Description state U32_t pointer to state holder Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_LOG_DATA_PTR_BAD Data holder pointer is null ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null Example Usage
S32_t status, state; ... // Get the system state status = oceos_system_state_get(&state);oceos_system_state_set()
Header File
system_log.h
Description
This function sets system state variable.Prototype
/** * Sets system state variable * * @param new_state * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null */ S32_t oceos_system_state_set( U32_t new_state // new value of system state variable );Parameters
Parameter Description new_state U32_t containing new system state Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null Example Usage
S32_t status, new_state; ... // Set new system state status = oceos_system_state_set(new_state);oceos_system_state_copy_get()
Header File
system_log.h
Description
This function returns the value of the system state copy variable.Prototype
/** * Returns the value of the copy of system state variable * * @param state pointer to state holder * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_LOG_DATA_PTR_BAD Data holder pointer is null * ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null */ S32_t oceos_system_state_copy_get( U32_t *state // pointer to state copy holder );Parameters
Parameter Description state U32_t pointer to state copy holder Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_LOG_DATA_PTR_BAD Data holder pointer is null ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null Example Usage
S32_t status, copy_state; ... // Get the system state copy status = oceos_system_state_copy_get(©_state);oceos_system_state_copy_set()
Header File
system_log.h
Description
This function loads a value to tha system state copy variable.Prototype
/** * Sets system state copy variable * * @param new_state * * @return OCEOS_SUCCESS * ERR_SYS_FIXED_CORRUPT System Fixed area corrupt * ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null */ S32_t oceos_system_state_copy_set( U32_t new_state // new value of system state variable );Parameters
Parameter Description new_state U32_t containing new system state copy Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
ERR_SYS_FIXED_CORRUPT System Fixed area corrupt ERR_SYS_LOG_CORRUPT LOG dynamic pointer is null Example Usage
S32_t status, new_state; ... // Set new system state copy status = oceos_system_state_copy_set(new_state);blank_function()
Header File
header.h
Description
This function does xyz...Prototype
S32_t oceosmp_blank( U32_t param );Parameters
Parameter Description param parameter to function Returns
This function returns an S32_t with a value of OCEOS_SUCCESS (zero) or return code bits set as defined in the table below.
Error bit Description Error_name description Example Usage
S32_t status, param; ... // Do xyz status = oceosmp_blank(param));